Showing results: 766 - 780 of 965 items found.
-
SOMA GmbH
Haptic tests are becoming ever more important owing to the increasing and sector-independent popularity of switches and buttons in diverse products. More and more customers, especially in the automobile sector, attach great value to good haptic performance by their control elements. A precise switching feeling, low friction of the moving elements, backlash-free execution both in the rest position and during operation are only some of the criteria for good haptic switching characteristics.
-
MK Test Systems Ltd.
These specialist Automeg models test the function and integrity of wiring harnesses combined with active components such as relays, switches, contactors, diodes, LEDS, actuators and other active components.Our software takes the complex and traditionally long task of creating functional tests away from the test engineer and allows these to be created automatically, from existing ECAD data and our component library and automated software routines. All the different routes and subtests are automatically calculated in seconds.
-
MK Test Systems Ltd.
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
DC3 -
Hilevel Technology, Inc.
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
570A -
B&K Precision Corporation
The Model 570A Analog IC Tester's built-in test library includes all common Analog ICs including op-amps, comparators, voltage regulators, voltage references, analog switches & multiplexes, opto-isolators & couplers, and audio ICs.
-
Dow-Key Mircowave Corporation
Dow-Key® Microwave offers PCB mounted, miniature electro-mechanical microwave switches. These switches are designed with an overall size of 0.75” x 0.75” x 0.58” and weight of 0.5 ounces for test and aerospace applications where small size, reduced weight, and less power consumption are critical.
-
Liona -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
1966A -
Peaceful Thriving Enterprise Co Ltd
*Check voltage on 70-440V AC.*With CE, cUL and RoHS Approval.*Operates by two LR44 1.5V batteries.*LED will glow if AC voltage is present.*Check for proper ground connection of electrical appliance.*Test electrical lines, cables, sockets, fuses, switches and etc.
-
Aero Nav Laboratories, Inc.
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
PEC N.V.
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
Aero Nav Laboratories, Inc.
The electrical contact testing is performed to determine the reliability of equipment under various contacting conditions. A few types of electrical contact tests are: contact-chatter monitoring, contact resistance, intermediate, and low level contact switching.
-
1081-001 -
Pickering Interfaces Ltd.
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
60-106-002 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 60-106-002 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. It features remote control via USB or LXI Ethernet and this version of the chassis includes Scan List Sequencing & Triggering. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.
-
60-106-001 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 60-106-001 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. The chassis features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.This chassis is also available with built-in scan list sequencing and triggering (model 60-106-002).
-
60-105-001 -
Pickering Interfaces Ltd.
This 4-slot USB/LXI modular chassis offers a small lightweight form factor, making it ideal for portable, benchtop, and space restrictive applications. The chassis is designed for desk or rack mounting and features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.